Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
This great article listed below in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is definitely fascinating. Give it a try and draw your own assumptions.
Installing a bathtub isn't exactly brain surgery, yet it does need strong plumbing, woodworking, and also often, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently easily accessible, the task can move speedily; if you need to open up a wall to eliminate the old bathtub and position the brand-new tub, the job is much harder. In either situation, the job is within a residence handyman's skills, although you will need a helper to leave the old bathtub and also embeded in the brand-new one. See to it you have qualified on your own for the work and fit trying it. Rather than employing a contractor to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This article will certainly assist you install a new bath tub in your bathroom if you have actually already gotten a brand-new bathtub and don't require to change the setup of your previous water pipelines.
Your tools and also material list must comprise the following:
Planning for the Installation
To start with, the sustaining frame provided with the bathroom should be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps system to prevent pressure on the bath tub.
Fit the flexible tap ports to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final placement.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is detach the supply of water. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The process of removing the existing faucets can be rather problematic because of the limited accessibility that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Before moving on to fit the new taps, compare the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Setting up the Tub
Using the two wooden boards under its feet, position the bath tub in the needed position. The wood boards are helpful in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the bath tub until the level reads level.
To mount taps, fit the bottom of the outermost adaptable tap port to the ideal supply pipe by making a compression join; then do the exact same for the other tap.
Switch on the water system and examine all joints and brand-new pipework for leakages and tighten them if necessary. Fill up the bath tub as well as additionally examine the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the tub ought to wait until the bath tub has actually been used a minimum of when as this will certainly resolve it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin making sure that the washing machines remain in place in between the tap and the sink. Protect the faucet in place with the supplier given backnut. When the tap is firmly in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former type needs to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, creating the water to pass through the wall surface in between the bath as well as the tiling, resulting in problems with moisture and feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the tub with water before sealing, to permit the motion experienced when the bathtub is in use. The sealer can crack relatively early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily offered on the market. It is a good idea to fit the floor tiles utilizing waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Create a review down below. We'd be interested to listen to your ideas about this article. We hope to see you back again before long. Are you aware of another individual who is fascinated about the topic? Why not share it. I truly appreciate reading our article about How to Install a Bathtub Yourself.
Get the best, call! Report this page